MF Skid
Dimensions(HtxDepthxWidth)
Data below applies to VN M and MF FG
series softeners (use as a guide).
Model No.
Skid A Skid B Configuration
Simplex
(See notes below)
MF-150-SX or SM
76”x48”x60” (1)
MF-240-SX or
SM 76”x48”x60” (1)
MF-300-SX or
SM 90”x60”x82” (1)
MF-450- SX or SM
90”x60”x82” (1)
MF-600- SX or SM
91”x66”x97” (1)
MF-750- SX or SM
103”x66”x97” (1)
MF-900- SX or SM
105”x80”x108” (1)
MF-1200- SX or SM
108”x84”x120” (1)
Twin
MF-150-TA
76”x48”x84” (2)
MF-240-TA
76”x48”x84” (2)
MF-300-TA
90”x60”x121” (2)
MF-450-TA 90”x60”x121”
(2)
MF-600-TA 91”x66”x136”
(2)
MF-750-TA 103”x66”x136”
(2)
MF-900-TA 105”x80”x120”
(3)
MF-1200-TA 108”x84”x126”
(3)
Triplex
MF-150-TX
76”x48”x114” (4)
MF-240-TX
76”x48”x114” (4)
MF-300-TX
90”x60”x121” (5)
MF-450-TX
90”x60”x121” (5)
MF-600-TX
91”x66”x136” (5)
MF-750-TX
103”x66”x136” (5)
MF-900-TX
105”x80”x120” 105”x80”x108” (6)
MF-1200-TX
108”x84”x126” 108”x84”x120” (6)
Quad
MF-150-Q 76”x48”x114”
(7)
MF-240-Q
76”x48”x114” (7)
MF-300-Q
90”x60”x121” 90”x60”x82” (8)
MF-450-Q
90”x60”x121” 90”x60”x82” (8)
MF-600-Q
91”x66”x136” 91”x66”x97” (8)
MF-750-Q
103”x66”x136” 103”x66”x97” (8)
MF-900-Q
105”x80”x120” 105”x80”x120” (9)
MF-1200-Q
108”x84”x126” 108”x84”x126” (9)
Configurations
(1)
One mineral tank and one brine tank on one skid
(2)
Two mineral tanks and one brine tank on one skid
(3)
Two mineral tanks on one skid – brine tank ships loose
(4)
Three mineral tanks and one brine tank on one skid
(5)
Three mineral tanks on one skid brine tank ships loose
(6)
Two skids – Skid A has two mineral tanks, Skid B has one mineral
tank and one, brine tank
(7)
Four mineral tanks on one skid – brine tank ships loose
(8)
Two skids – Skid A has three mineral tanks, Skid B has one
mineral tank and one brine tank
(9)
Two skids – Skid A has two mineral tanks, Skid B has two mineral
tanks, brine tank ships loose
(10)
Each mineral tank on a separate skid, brine tank ships loose
MF Skid Standard
Features.
Also
applies to MF FG and VN M Series softeners.
System shall be mounted on a blue epoxy coated carbon steel skid.
Controls shall be pre-wired using non-metallic liquid-tite flex conduit.
Vessels shall be bolted to the skid. The skid shall be pre-piped with
piping firmly supported on the skid. Pipe supports shall be U-bolts on
2” angle iron or Unistrut. Standard skid piping shall include schedule
40 grooved or threaded galvanized pipe for the inlet and outlet. Brine
line shall be poly propylene tubing or solvent welded schedule 80 PVC.
Drain lines shall be (¾” or 1 ½” solvent welded schedule 80 PVC). Inlet
and outlet isolation valves for each vessel and a bypass valve shall be
provided. 1 ½” and 2” valves shall be threaded quarter turn cast bronze
ball valves with stainless steel ball. 2 ½” and larger valves shall be
grooved quarter turn cast iron body butterfly valves. Slots shall be
provided in the skid for forklift tines. Piping and vessels shall be
hydro test at 100 psi for 1 hour. Pressure gauges and test tap kits
shall be installed. Internals for vessels 48 inches and larger in
diameter (model 1200) shall ship loose to avoid damage during transit.
Models 150 – 750 shall ship with the brine tank mounted on the skid.
For models 900 and larger both mineral tanks shall be mounted on a
single skid and the brine tank shall not be mounted on the skid and
shall ship loose. Media shall ship loose and must be loaded on site.
Single point electrical connection shall be provided for all skids.
Power requirement shall be 110V, 1Ø, 60 Hz, 5 AMPS. (Drive motor is
3.2 amps and solenoid is 10.5 Watts.)
MF, MF FG, and VN M Series Softeners - Skid Mounting